WE FLIP it over and you can see Mustang written on the module.ħ. AS SEEN, the Classic Design Concepts sequential module is very small.Ħ. LOUIE TRIMS back the wiring on the pigtails on the new sockets.ĥ.
A little tweaking and they will fit your Ford housings.Ĥ. Calterm manufactures this unit but many companies have them. WE START with brand-new sockets to install new bulbs into our taillight housing. Might as well accept it, it’s a Digital World we live in.ģ. The new kit, on the other hand, comes with small modules that Ford made for 2005 to 2009 Mustangs. THIS IS the old brain that Mercury installed, and it is susceptible to failure after having been on the streets for more than four decades, much like the old “dynamite sticks” that Ford/ Mercury first installed in Shelbys and Cougars. We will retrofit our car to handle this system.Ģ. As seen here, Classic Design Concepts has a system for late model Mustangs to convert them.
We decided to convert this one to a new-style fully electronic system for more reliability compared to the old “dynamite sticks” used by Ford/Mercury in 1969. STOCK COUGARS were known for their sequential taillights and the customers want to keep them operational. The following restoration project was performed in our shop on a vintage Mercury Cougar, but the equipment used will work on any model vehicle with a 2- to 4-bulb tail light setup that you want to convert into a sequential turn signal system.ġ. This Electronic Setup Will Bring Back the Life to a Cougar’s Tail and a Mustang’s as Well. We feel these Dodge Challenger Sequential turn signal taillights are the best exterior modification you can make.Novem| By Jeff Lilly Cougars Are Known for Flicking Their “Tail” Lights, But With Passing Decades the System May Fail. Once you have completed these steps, go back to the 2008-2010 instructions and continue at Step 17. Insert the TAN/GREEN wire from the trunk switch into the hole of the new harness. Remove the dummy plug that's in the connector. Then fold the cover over.ġ6E) Remove the brown wire retainer from the 4-pin connector. Using a pair of pliers, squeeze the metal tab on the quick- splice until it is flush with the connector body. Using the supplied quick- splice, connect the BLACK/GREEN switch wire to the BLACK wire on the new harness. Replace the retainer above.ġ6D Find the new Tail Light Harness (Part A). 16B) Using a small screwdriver, remove the brown wire retainer from the connector on the OEM harness.ġ6C) Insert a small screwdriver at the terminal side to release the TAN/GREEN wire. Cut the BLACK/GREEN wire coming from the trunk switch. The connector will slide off leaving the retainer in the fixture.ġ6A) Refer to the pictures below. Follow the instructions for the 08-10 Challenger, and take these additional steps: 16) Remove the connector from the panel using a large screwdriver. If your car has this, you will need to move one wire and cut/splice one ground wire from your OEM harness to the new tail light harness. Some 2011+ Challengers have a trunk release button under the spoiler. These lights will fit any 2008-2014 Dodge Challenger, including SE, R/T and SRT8. While other products offer you fixed timing or complicated manual adjustments, our electronics sense your Challenger's flasher speed and adjust the sequence timing for you. These harnesses feature sophisticated electronics that automatically adjust the sequencing speed to match the turn signal flasher in your car. This Challenger sequential tail light kit contains pre-wired, plug-in harnesses that install with no wire cutting or splicing of any kind! These 2008-2014 Dodge Challenger sequential taillight kits will convert the taillights on your 2008-2014 Dodge Challenger into Sequential Turn Signals. These 2008-2014 Dodge Challenger sequential taillight kits are sure to raise your Challenger to a new level. (2011 - 2014 Dodge Challenger Models require cutting) 2008-2014 Dodge Challenger Sequential Taillights Kit
0 kommentar(er)
